FILE NAME: hp-qlcnic-5.0.17.4-3.src.rpm TITLE: HP NC-Series QLogic qlcnic Driver for Linux VERSION: 5.0.17.4 RELEASE: 3 LANGUAGE: English CATEGORY: Software Solutions DIVISIONS: Enterprise and Mainstream Servers EFFECTIVE DATE: 12/08/11 SUPERSEDES: 5.0.17.4-2 Products Affected ================== HP CN1000Q Dual Port Converged Network Adapter HP NC523SFP Dual port 10GbE Server Adapter Operating Systems ================== Red Hat Enterprise Linux 6 Update 2 for AMD64/EM64T Red Hat Enterprise Linux 6 Update 2 for x86 Red Hat Enterprise Linux 6 Update 1 for AMD64/EM64T Red Hat Enterprise Linux 6 Update 1 for x86 Red Hat Enterprise Linux 6 for AMD64/EM64T Red Hat Enterprise Linux 6 for x86 Red Hat Enterprise Linux 5 Update 7 for AMD64/EM64T Red Hat Enterprise Linux 5 Update 7 for x86 Red Hat Enterprise Linux 5 Update 6 for AMD64/EM64T Red Hat Enterprise Linux 5 Update 6 for x86 SUSE LINUX Enterprise Server 11 Service Pack 1 for AMD64/EM64T SUSE LINUX Enterprise Server 11 Service Pack 1 for x86 SUSE LINUX Enterprise Server 11 for AMD64/EM64T SUSE LINUX Enterprise Server 11 for x86 SUSE LINUX Enterprise Server 10 Service Pack 4 for AMD64/EM64T SUSE LINUX Enterprise Server 10 Service Pack 4 for x86 SUSE LINUX Enterprise Server 10 Service Pack 3 for AMD64/EM64T SUSE LINUX Enterprise Server 10 Service Pack 3 for x86 Pre-requisites =============== ProLiant server supporting above operating systems 2 GB RAM minimum Latest HP System ROM Build Environment Setup NOTE: Visit the following URL and download latest System ROM http://welcome.hp.com/country/us/en/support.html Select "Download drivers and software" Description ============ This RPM contains HP tested and approved Ethernet driver for use with network adapters mentioned in the PRODUCTS AFFECTED section of this document. Enhancements/Fixes =================== 1) Added KMP build support for RHEL6 Update 2 Table of Contents ================= Introduction Packaging Build Environment Setup Installing the RPM Package Uninstalling the RPM Package Caveats Introduction ============ This file describes how to build and install the Ethernet driver for network adapters mentioned in the PRODUCTS AFFECTED section. Additional information for the Ethernet driver can be found in the driver man page which gets installed on installing the tools rpm. The tools rpm gets built along with the KMP binary rpm. User guides and additional HP Network Adapter information can be found at: http://h18004.www1.hp.com/products/servers/networking/index-nic.html Packaging ========= The driver is released in Kernel Module Package (KMP) source RPM format. KMP packages use macros that determine kernel flavors for which binary need to be built based on spec file rules. It is important to have the right build environment set up in order to compile a binary RPM from source package. See "Build Environment Setup" section below for more details. Build Environment Setup ======================== This package requires the presence of certain other packages that provide the right build environment to enable building a KMP binary rpm from the source rpm. These packages provide kernel headers, makefiles and symbol files. Please ensure that the following are installed: RHEL installation: 1. redhat-rpm-config package 2. kernel-devel-<kernel_version> package 3. kernel-<flavor>-devel-<kernel_version> package Eg: kernel-2.6.18.92.el5 requires kernel-devel-2.6.18-92.el5 kernel-PAE-2.6.18.92.el5 requires kernel-PAE-devel-2.6.18-92.el5 See the "Caveats" section below for more details. SLES Installation: 1. kernel-source-<kernel_version> package 2. kernel-syms-<kernel_version> package 3. SLES11 requires kernel-<flavor>-devel-<kernel_version> package in addition to the above two mentioned Installing the RPM Package ============================= 1. This package requires a specific build environment. Please refer the "Build Environment Setup" section above before proceeding. 2. Install the source RPM package. # rpm -ivh hp-qlcnic-<version>.src.rpm 3. Build the binary RPM for the qlcnic package. RHEL 5: # rpmbuild -bb /usr/src/redhat/SPECS/hp-qlcnic.spec RHEL 6: # rpmbuild -bb ~/rpmbuild/SPECS/hp-qlcnic.spec SLES: # rpmbuild -bb /usr/src/packages/SPECS/hp-qlcnic.spec If you get an error during the build process, refer to the "Build Environment Setup" section. NOTE: One can build binary RPM for a specfic kernel flavor as follows: # rpmbuild -bb SPECS/hp-qlcnic.spec --define "KVER <kver>" NOTE: RHEL 5 x86 installations require the "--target" switch when building on Intel compatible machines. Please see the "Caveats" section below for more details. # rpmbuild --target=i686 -bb /usr/src/redhat/SPECS/hp-qlcnic.spec 4. Check for the existence of a current version of the hp-qlcnic package as follows: RHEL # rpm -q kmod-hp-qlcnic-<flavor> SLES # rpm -q hp-qlcnic-kmp-<flavor> If an old version of the RPM package exists, it should be removed as follows. Remove the corresponding tools package before removing the driver package itself. RHEL # rpm -e kmod-hp-qlcnic-<flavor> SLES # rpm -e hp-qlcnic-kmp-<flavor> Verify if the old hp-qlcnic package has been removed as follows: RHEL # rpm -q kmod-hp-qlcnic-<kernel flavor> SLES # rpm -q hp-qlcnic-kmp-<kernel flavor> 5. If an older version of qlcnic.ko is loaded into the kernel, remove it as follows. Note: If you are installing the package over network you may want to be careful. It is not absolutely necessary to remove the modules. This step is necessary if you are doing the upgrade on the physical console and you intend to see the new drivers taking over immediately # lsmod | grep qlcnic Bring down the interfaces controlled by qlcnic # ifconfig eth<n> down Uninstall the existing active driver # modprobe -r qlcnic 6. Install the new binary RPM package. This installs the qlcnic driver RHEL 5 # rpm -ivh \ /usr/src/redhat/RPMS/<arch>/kmod-hp-qlcnic-<flavor>-<version>.<arch>.rpm RHEL 6 # rpm -ivh \ ~/rpmbuild/RPMS/<arch>/kmod-hp-qlcnic-<flavor>-<version>.<arch>.rpm The modules are installed in the following directory: /lib/modules/<kernel_version>/extra/hp-qlcnic Note: The "--nodeps" switch is required when installing on RHEL 5.4, 5.5 and 5.6. See "Caveats" section below for more details. # rpm -ivh \ /usr/src/redhat/RPMS/<arch>/kmod-hp-qlcnic-<flavor>-<version>.<arch>.rpm --nodeps SLES # rpm -ivh RPMS/<arch>/hp-qlcnic-kmp-<version>-<flavor>.<arch>.rpm The modules are installed in the following directory: /lib/modules/<kernel_version>/updates/hp-qlcnic 7. Run "modinfo qlcnic | grep version" and verify that the driver version is latest 8. Run "modprobe qlcnic" to install latest "qlcnic" driver module 9. Configure your network setting and address. You may need to refer to your Linux vendor documentation. Helpful network configuration tools such as "yast2" in SLES or linuxconf/redhat-config-network/ netconfig in Red Hat exist for easy configuration. Uninstalling the RPM Package =============================== The following command will uninstall the RPM. Red Hat # rpm -e kmod-hp-qlcnic-<kernel flavor> SLES # rpm -e hp-qlcnic-kmp-<kernel flavor> Caveats ======= 1. The rpmbuild will fail the dependency check when building the non-base (xen,pae,etc) kernel when the kernel-devel package is not installed. Example: If the OS only included the PAE kernel then the user would need to install the kernel-pae-devel and kernel-devel packages. 2. The use of a "--target" switch is required so that rpmbuild does not try to find an i386 kernel on the system. If the "--target" switch is not used then the build will fail with bizarre messages stating that specific kernel packages are not installed on the machine yet these pacakges do not exist. 3. The rpmbuild will fail if the redhat-rpm-config package is not installed because it cannot resolve the %kernel_module_package_buildreqs macro. The error will be similar to the following: error: line xx: Dependency tokens must begin with alpha-numeric,'_'or'/': BuildRequires: %kernel_module_package_buildreqs 4. RPM uses KMP packaging dependency data to ensure the dependencies are met before installing the binary RPM. Red Hat maintains a whitelist of kernel symbols which RPM uses to validate against the KMP binaries. Some symbols may be in the kernel but not on the whitelist which results in a failed binary RPM install. The user will need to use the "--nodeps" switch when installing the binary. The qlcnic packaged drivers uses the following symbols on RedHat EL5 Update 4 and Update 5 that are not on the whitelist: ksym(pci_get_domain_bus_and_slot) ksym(pci_cleanup_aer_uncorrect_error_status) ksym(pci_disable_pcie_error_reporting) ksym(pci_enable_pcie_error_reporting) ksym(napi_gro_flush) (C) Copyright 2011 Hewlett-Packard Development Company, L.P. Product names mentioned herein may be trademarks and/or registered trademarks of their respective companies.