FILE NAME:	CP015143.scexe

TITLE:		HP NC-Series Broadcom Online Firmware Upgrade 
		Utility for Linux i386

VERSION:	2.4.25

REVISION:	0

LANGUAGE:	English

CATEGORY:	Software Solutions

DIVISIONS:	Enterprise and Mainstream Servers

EFFECTIVE DATE:	12/22/2011

SUPERSEDES:	CP014347.scexe


Products Affected
==================
HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter
HP Flex-10 10Gb 2-port 530FLB Adapter
HP Flex-10 10Gb 2-port 530M Adapter
HP Ethernet 1Gb 4-port 331FLR Adapter
HP Ethernet 1Gb 4-port 331T Adapter
HP Ethernet 1Gb 4-port 331i Adapter
HP NC1020 Gigabit Server Adapter 
HP NC6770 Gigabit Server Adapter
HP NC7760 Gigabit Server Adapter
HP NC7761 Gigabit Server Adapter
HP NC7770 Gigabit Server Adapter
HP NC7771 Gigabit Server Adapter
HP NC7780 Gigabit Server Adapter
HP NC7781 Gigabit Server Adapter 
HP NC7782 Gigabit Server Adapter 
HP NC150T PCI 4-Port Gigabit Combo Switch Adapter
HP NC320T PCIe Gigabit Server Adapter
HP NC320I PCIe Gigabit Server Adapter
HP NC320M PCIe Adapter
HP NC324I PCIe Dual Port Gigabit Server Adapter
HP NC325M PCIe Quad Port Gigabit Server Adapter
HP NC326I PCIe Dual Port Gigabit Server Adapter
HP NC326M PCIe Dual Port Adapter
HP NC370T Multifunction Gigabit Server Adapter
HP NC370F Multifunction Gigabit Server Adapter
HP NC370i Multifunction Gigabit Server Adapter
HP NC371i Multifunction Gigabit Server Adapter
HP NC373T PCIe Multifunction Gig Server Adapter
HP NC373F PCIe Multifunction Gig Server Adapter
HP NC373i PCIe Multifunction Gig Server Adapter
HP NC373m PCIe Multifunction Gig Server Adapter
HP NC374m PCIe Multifunction Adapter
HP NC380T PCIe DB Mulitfunc Gig Server Adapter
HP NC382i DP Multifunction Gigabit Server Adapter
HP NC382T PCIe DP Multifunction Gigabit Server Adapter
HP NC382m DP 1GbE Multifunction BL-c Adapter
HP NC532i Dual Port 10GbE Multifunction BL-c Adapter
HP NC532m Dual Port 10GbE Multifunction BL-c Adapter
HP NC105i PCIe Gigabit Server Adapter
HP NC107i PCIe Gigabit Server Adapter


Operating Systems
==================
Red Hat Enterprise Linux 6 Update 2 for x86
Red Hat Enterprise Linux 6 Update 1 for x86
Red Hat Enterprise Linux 6 for x86
Red Hat Enterprise Linux 5 Update 7 for x86
Red Hat Enterprise Linux 5 Update 6 for x86

SUSE LINUX Enterprise Server 11 Service Pack 1 for x86
SUSE LINUX Enterprise Server 11 for x86
SUSE LINUX Enterprise Server 10 Service Pack 4 for x86
SUSE LINUX Enterprise Server 10 Service Pack 3 for x86


Pre-requisites
===============
ProLiant server supporting above operating systems
2GB RAM minimum
tg3 Linux driver version >= 3.58b
bnx2 Linux driver version >= 1.4.41
bnx2x Linux driver version >= 1.45.19


Description
============
This scexe contains the utilities and binaries for upgrading 
HP ProLiant Gigabit Ethernet NICs boot code, PXE, IPMI, UMP, 
CLP, and iSCSI code running under Linux x86 platform.


Enhancements/Fixes
===================
1) Added support for HP Ethernet 1Gb 4-port 331FLR Adapter
2) Added support for HP Ethernet 1Gb 4-port 331T Adapter
3) Added support for HP Ethernet 1Gb 4-port 331i Adapter
4) Added support for HP Ethernet 10Gb 2-port 530FLR-SFP+ Adapter
5) Added support for HP Flex-10 10Gb 2-port 530FLB Adapter
6) Added support for HP Flex-10 10Gb 2-port 530M Adapter
7) Updates bootcode for NC532x devices to v6.2.10
8) FIX: NVRAM read failure during CLP FW update on 465 G6 NC370i


Table of Contents
=================
Introduction
Packaging
Performing the Firmware Upgrade
Firmware Upgrade Log
Configure IPMI: Disable/Enable


Introduction
============
This file describes the procedure to use for upgrading firmware
on HP Gigabit Server Adapters mentioned in the PRODUCTS AFFECTED
section of this document.

User guides and additional HP Network Adapter information can be found at:
http://h18004.www1.hp.com/products/servers/networking/index-nic.html
 
Packaging
=========
This firmware upgrade utility is released in SCEXE format. The
file is a single self-extracting executable that unpacks the
component, runs it, and cleans up. This one-step process replaces
the rpm format which would require three steps to install, execute
and remove.


Performing the Firmware Upgrade
===============================
1. This utility requires the ethernet interface to be up. You can 
bring up an ethernet interface by using the following command:

	# ifup ethx

	or

	# ifconfig ethx up

2. Firmware can be upgraded interactively using following command:

	# ./CP00xxxx.scexe

3. The help menu lists all available command line options.

	# ./CP00xxxx.scexe -h


Firmware Upgrade Log
====================
Results of the firmware upgrade are written to nicfwupg.log which 
gets saved in the current working directory.

	
Configure IPMI: Disable/Enable
==============================
1. This utility requires the ethernet interface to be up. You can
bring up an ethernet interface by using the following command:

	# ifup ethx

	or

	# ifconfig ethx up

2. Verify current configuration status using the following command:

	# ./CP00xxxx.scexe -c

3. Configure IPMI by sending the following command:

	# ./CP00xxxx.scexe [ interface ] ipmi [ options ]

	options:
	0 - Disable IPMI
	1 - Enable IPMI

Example: The following command disables IPMI

	# ./CP00xxxx.scexe eth0 ipmi 0

Note: Please refer to the adapter QuickSpecs for information on 
supported features.

Copyright 2011 Hewlett-Packard Development Company, L.P.
Product names mentioned herein may be trademarks and/or registered trademarks
of their respective companies